Off‐grid DoA estimation method of wideband signals

In this paper, an off‐grid direction of arrival (DoA) estimation method is proposed for wideband signals. This method is based on the sparse representation (SR) of the array covariance matrix. Similar to the time domain DoA estimation methods, the correlation function of the sources was assumed to be the same and known. A new measurement vector is obtained using the lower‐left triangular elements of the covariance matrix. The DoAs are estimated by quantizing the entire range of continuous angle space into discrete grid points. However, the exact DoAs may be located between two grid points; therefore, this estimation has errors. The accuracy of DoA estimation is improved by the minimization of the difference between the new measurement vector and its estimated values. Simulation results revealed that the proposed method can enhance the DoA estimation accuracy of wideband signals.     

干扰条件下的“北斗”信号解扩重构DOA估计

在干扰条件下，卫星导航抗干扰波束形成算法往往需要卫星信号波达方向（Direction-of-Arrival，DOA）的先验信息。但当存在低信噪比信号或主动干扰源时，常规的DOA估计算法性能急剧下降甚至失效。针对此问题，提出了一种被干扰信号压制的低信噪比“北斗”信号的DOA估计算法。该算法首先通过对接收信号进行子空间投影抑制干扰信号，然后对抑制干扰后的信号进行解扩重构处理，最后通过多重信号分类算法完成对“北斗”信号的DOA估计。仿真结果表明，在干扰信号干信比80 dB条件下，“北斗”信号DOA估计误差在5°以内，为下一步进行波束形成计算提供了高精度的入射角信息。     

烟道流量计量标准装置

为了解决我国烟道流量计的量值溯源问题,中国计量科学研究院建立了烟道流量计量标准装置。装置使用可溯源至标准转盘的激光多普勒测速仪作为原级标准器,采用激光多普勒流速剖面扫描和超声流量计波动修正的方式测量标准流量,经校准的8声道超声流量计为工作级标准表,具备了908~104840m3/h的测量能力,扩展不确定度为0.62%(k=2),可对最大口径为1m的流量计进行校准。装置下游测试段包括圆形管段和矩形管段,能够开展烟道流量计测量性能的研究。     

内热型超声雾化溶液再生系统最优内热量的研究

基于质量守恒、能量守恒定律，建立了内热型超声雾化溶液再生系统（IH-UARS）的再生性能预测模型并进行了充分的实验验证，通过研究不同内热量下IH-UARS的再生性能及其变化规律，寻求系统所需的最佳内热量并明确其可能的影响因素。结果表明：IH-UARS系统存在最优的内热量范围，使其再生系统性能最佳；所需最优内热量随着再生溶液流量增大呈显著的对数增长，但受空气流量的影响较弱；在该研究中的标准工况下，IH-UARS所需最优内热量约为275~350 W。此外研究发现：内热量的增长有益于促进初始浓度较高的溶液进一步浓缩再生，如当IH-UARS中内热量增至800 W时，其初始浓度为36%的溶液比24%的溶液浓度增量指标改善幅度高37%。研究所得结果可对提高溶液再生性能及经济性提供积极参考。     

换能器结构参数对聚合物超声塑化黏弹生热的影响

为研究超声换能器结构参数对聚合物超声塑化过程黏弹性生热的影响，首先确定超声黏弹性生热系统的组成，进行纵振超声换能器结构设计；然后分析超声黏弹性生热过程及超声黏弹性生热原理；最后采用单一变量法分析超声换能器的主要结构参数对其纵振频率及工具头前端质点最大振幅的影响，将其实际输出的纵振激励加载于熔融聚合物，研究其结构参数对聚合物超声黏弹性生热过程及达到聚合物玻璃化转变温度所用时间的影响。结果表明，随纵振激励作用时间的增加，聚合物温度非线性升高；放大比对聚合物温度变化影响最大，前盖板厚度和工具头长度次之，影响最小的是变幅杆长度。     

Nonuniform linear array DOA estimation using EM criterion

In this letter, we address the problem of Direction of Arrival (DOA) estimation with nonuniform linear array in the context of sparse Bayesian learning (SBL) framework. The nonuniform array output is deemed as an incomplete-data observation, and a hypothetical uniform linear array output is treated as an unavailable complete-data observation. Then the Expectation-Maximization (EM) criterion is directly utilized to iteratively maximize the expected value of the complete-data log likelihood under the posterior distribution of the latent variable. The novelties of the proposed method lie in its capability of interpolating the actual received data to a virtual uniform linear array, therefore extending the achievable array aperture. Simulation results manifests the superiority of the proposed method over off-the-shelf algorithms, specially on circumstances such as low SNR, insufficient snapshots, and spatially adjacent sources.     

基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Bond graph modeling,design and experimental validation of a photovoltaic/fuel cell/ electrolyzer/battery hybrid power system

This work presents a complete bond graph modeling of a hybrid photovoltaic-fuel cell-electrolyzer-battery system. These are multi-physics models that will take into account the influence of temperature on the electrochemical parameters. A bond graph modeling of the electrical dynamics of each source will be introduced. The bond graph models were developed to highlight the multi-physics aspect describing the interaction between hydraulic, thermal, electrochemical, thermodynamic, and electrical fields. This will involve using the most generic modeling approach possible for managing the energy flows of the system while taking into account the viability of the system. Another point treated in this work is to propose. In this work, a new strategy for the power flow management of the studied system has been proposed. This strategy aims to improve the overall efficiency of the studied system by optimizing the decisions made when starting and stopping the fuel cell and the electrolyzer. It was verified that the simulation results of the proposed system, when compared to simulation results presented in the literature, that the hydrogen demand is increased by an average of 8%. The developed management algorithm allows reducing the fuel cell degradation by 87% and the electrolyzer degradation by 65%. As for the operating time of the electrolyzer, an increment of 65% was achieved, thus improving the quality of the produced hydrogen. The Fuel Cell's running time has been decreased by 59%. With the ambition to validate the models proposed and the associated commands, the development of this study gave rise to the creation of an experimental platform. Using this high-performance experimental platform, experimental tests were carried out and the results obtained are compared with those obtained by simulation under the same metrological conditions.